The SunStat 500710 is a Basic Non-Programmable Control used to control the floor temperature of a SunTouch electric floor heating system. This simple control is easy to install and has a built-in GFCI and 15 amp relay so you can control up to 150 sq. ft. of 120V or 300 sq. ft. of 240V SunTouch mats.

Senses the FLOOR Temperature (Using the INCLUDED floor Sensor Wire) and has Built-in Ground Fault Protection with no need for an additional GFCI circuit in most areas.

• Large temperature setting dial
• 15 Amp capacity to control up to 150 SF of SunTouch 120VAC mats per control (300 SF of 240v mats)
• No Programming necessary - Simple & Easy to operate
• 1 Year Factory Warranty
• Manufactured in Europe by Watts
• On/Off switch is located on side of control
• GFCI Test button on side of the SunStat 500710

Additional Information

SunStat 500710 Installation

The SunStat 500710 is a Basic Non-Programmable Control used to control the floor temperature of a SunTouch electric floor heating system. This simple control is easy to install and has a built-in GFCI and 15 amp relay so you can control up to 150 sq. ft. of 120V or 300 sq. ft. of 240V SunTouch mats.

Senses the FLOOR Temperature (Using the INCLUDED floor Sensor Wire) and has Built-in Ground Fault Protection with no need for an additional GFCI circuit in most areas.

• Large temperature setting dial
• 15 Amp capacity to control up to 150 SF of SunTouch 120VAC mats per control (300 SF of 240v mats)
• No Programming necessary - Simple & Easy to operate
• 1 Year Factory Warranty
• Manufactured in Europe by Watts
• On/Off switch is located on side of control
• GFCI Test button on side of the SunStat 500710

Additional Information

SunStat 500710 Installation

The SunStat 500710 is a Basic Non-Programmable Control used to control the floor temperature of a SunTouch electric floor heating system. This simple control is easy to install and has a built-in GFCI and 15 amp relay so you can control up to 150 sq. ft. of 120V or 300 sq. ft. of 240V SunTouch mats.

Senses the FLOOR Temperature (Using the INCLUDED floor Sensor Wire) and has Built-in Ground Fault Protection with no need for an additional GFCI circuit in most areas.

• Large temperature setting dial
• 15 Amp capacity to control up to 150 SF of SunTouch 120VAC mats per control (300 SF of 240v mats)
• No Programming necessary - Simple & Easy to operate
• 1 Year Factory Warranty
• Manufactured in Europe by Watts
• On/Off switch is located on side of control
• GFCI Test button on side of the SunStat 500710

Additional Information

SunStat 500710 Installation

The SunTouch 500680 SunStat Relay is designed to control the voltage to either a 120VAC or 240VAC resistive floor warming system. It must be driven by a SunStat thermostat to operate, 500670 (programmable) or 500675 (non programmable). The 500680 Replaces the CT230-xxx SlaveStat models.

The Sunstat Relay allows you to expand an existing or new installation of Suntouch Floor Heating; you may drive up to 10 SunStat Relays with one SunStat thermostat acting as the Master control of all attached relays (up to 10). This allows 1 thermostat to control up to 10 circuits of floor warming.

This Relay is Dual Voltage for either 120v or 240v - You can't get it wrong! Power and floor heating is connected to each relay (just like a thermostat) and then low voltage wire connects each relay to the Thermostat.

When you use the Sunstat Relay with the NEW Programmable SunStat PRO control, these New Features provide the Ulitmate heated floor control

• Dual Voltage - 1 thermostat for Either 120v or 240 - never have the wrong thermostat on the job again.
• Air-sensing Mode with a Floor Temperature override limit as an option
• Regulator mode if sensor not connect or is damaged
• "Master" Control Capability - Each SunStat Pro allows other SunStat Relays to be connected to it to expand your system
• Class 2 Insulated Sensor ( 15' long) Wire which can run in the SAME CONDUIT as the power lead from your Floor Heater system
• 5/1/1 Day Programming mode or manual option
• Four Preset Schedules are included - choose one that suits you or program your own!
• Usage Monitoring - Your SunTouch SunStat Pro can report the on time of your SunTouch Floor Heat system
• 12 or 24 hour (military time) Display - your choice
• SmartStat Technology
• Easily Integrates with your home automation system (dry contact relay)

Other Features of the 500680 Relay when used with the 500670 SunStat Pro:

• Temperature Range (floor) of 40 to 99 degrees F (5 to 37 Celsius)
• Large Digital Display showing operation, mode, heat on/off, etc. LCD shows time and all functions
• Temperature displays in either F or C
• 15 Amp capacity to control up to 150 SF of SunTouch 120VAC mats per control and 300 SF of 240v SunTouch
• Can connect to NEW remote FloorStat sub control relay 500680
• Built-In Class A GFCI protection with GFCI test Light and button - 5 milliAmp trip
• 1 Year Warranty
• No Battery required - Your programming is saved in memory indefinitely
• Manual Setback / Vacation Mode for quick switching to Economy setting when leaving for an extended time
• MANUAL mode is also available to over-ride your program. Many customers like the look of this programmable model, but use it as a manual control

Included with Each SunStat Relay:

• Small Screwdriver for making connection
• Wirenuts for wiring connections
• Mounting Screws

Additional Information

500680 Instructions PDF Print, Read or save

Special Order - 5-7 Day Lead Time

Ultimate convenience! Control your thermostat plus three other household devices from a touch-tone phone. 4 universal relay outputs (dry contact) Each output operates independently.

Universal outputs (4) work with thermostats and household devices operating with dry contacts.

Download Instructions

Compatible with the following thermostats (or any with a dry contact relay input) All SunTouch Thermostats and the Tempo. Not compatible with any other Nuheat thermostats.

• Connects directly to existing phone line
• Activated by home / cell phones and is compatible with answering machines
• One-touch buttons enable manual override of controller output status
• LEDs show output status
• Programming ring setting enable user to select number of rings (1 to 9) before controller answers
• Battery-free backup saves user settings and output status after a power outage
• Password-protected for secure access

POWER SUPPLY
9 VAC / 60 Hz (adapter and phone cable included)

OUTPUTS
Universal relay output
5 A @ 30 VAC inductive P.F. 0.4
10 A @ 30 VAC resistive
10 A @ 120 / 240 VAC resistive (electrical box required)

DIMENSIONS (HxWxD)
69 x 137 x 31 mm / 2.7 x 5.4 x 1.2 inches

Special Order - 5-7 Day Lead Time

This Basic Dial Thermostat is available for a limited time only and we offer it at this terrific price.

The NEW Digital non-programmable control is only a few dollars more and is the latest generation of floor warming thermostats.

Or, Choose the Number 1 floor heating control, brand new and packed with features...

SunStat Pro Programmable Thermostat LCD

Additional Information

FloorStat Instructions

SunStat Sensor Wire is 15 Ft Long For Programmable or Non-Programmable Thermostats.

1 Sensor is included with each thermostat.

Customers ask: Do I need an extra floor sensor wire? We formerly recommended it. But, if you CHECK the resistance of the sensor, as indicated in the instructions, we don't feel it's necessary. Each sensor is labeled with instructions.

Some customers orders an extra sensor for "peace of mind". Although it is extremely rare for a sensor to fail, they think it is a reasonable precaution to install 2 sensor wires and they consider it cheap insurance.

If you choose to purchase 2 sensors, run both sensors from the control box to the floor below and then place them between the heating elements 12 inches or more into the heated portion of the floor. You can put them side by side, but connect only one to the thermostat control. If you ever need to replace a faulty sensor, you will have one at your fingertips; simply disconnect one, and connect the back-up.

All of our controls include a sensor wire; however, a spare can come in handy if yours gets lost or damaged during installation.

Each Thermostat Manufacturer uses a different sensor wire.

The SunTouch 500675 NON-programmable Thermostat's NEW clean design and features make it the Top rated Basic T-stat to control your Floor heating system.

This thermostat senses the FLOOR Temperature (Using the INCLUDED 15 foot Floor Sensor Wire) and has Built-in Ground Fault Protection for your safety. Listed by ETL to UL standards for use in the USA and Canada. No need for an additional GFCI circuit in most areas. Buttons are out of sight behind a single door at the bottom of the SunStat, just below the backlit digital display.

Push a button to raise or lower temperature or simply turn the system off.

This Thermostat is Dual Voltage - 1 thermostat for either 120v or 240v - You can't get it wrong!

Several New Features were added when creating this thermostat, which was released in Sept 2007 and is Manufactured by SunTouch - not outsourced like most manufacturers.

New Features make the SunStat a terrific value if you don't want programming features to control your Floor Heating System.

• Dual Voltage - 1 thermostat for Either 120v or 240 - never have the wrong thermostat on the job again
• Air-sensing Mode with a Floor Temperature override limit as an option
• Regulator mode if sensor is not connect or is damaged
• "Master" Control Capability - Each SunStat Pro allows other SunStat Relays to be connected to it to expand your system
• Class 2 Insulated Sensor ( 15' long) Wire which can run in the SAME CONDUIT as the power lead from you Floor Heater system
• 12 or 24 hour (military time) Display - your choice
• SmartStart Control

Other Features:

• Temperature Range (floor) of 40 to 99 degrees F (5 to 37 Celsius)
• Back Light for LCD screen
• Large Digital Display showing operation, mode, heat on/off, etc. LCD shows time and all functions
• Temperature displays in either F or C
• 15 Amp capacity to control up to 150 SF of SunTouch 120VAC mats per control and 300 SF of 240v SunTouch
• Can connect to NEW remote FloorStat Control unit
• Built-In Safety - Class A GFCI protection with GFCI test Light and button - 5 milliAmp trip
• 1 Year Warranty
• No Battery required
• Manual Setback / Vacation Mode for quick switching to Economy setting when leaving for an extended time

Included with Each Thermostat:

• 15 Foot Sensor Wire (Class 2 Insulated sensor - the best in the business) can be cut shorter if you choose
• Complete Instructions in English, Spanish & French
• Screwdriver included for use in installation
• Wire Nuts
• Mounting Screws

Additional Information

500675 Instructions PDF - Read, Print or save

The SunTouch 500670 Programmable Floor Heating Thermostat's NEW clean design makes it the Ultimate choice for control of your Floor heating system. This thermostat senses the FLOOR Temperature (Using the INCLUDED 15 foot Floor Sensor Wire) and has Built-in Ground Fault Protection for your safety and is listed by ETL to UL standards for use in the USA and Canada. No need for an additional GFCI circuit in most areas. Programming buttons are out of sight behind a single door at the bottom of the SunStat Pro, just below the backlit digital display.

>>> New lower special Price for a Limited Time ! <<<

This Thermostat is Dual Voltage - 1 thermostat for either 120v or 240v - You can't get it wrong!

Several New Features were added when creating this thermostat, which was released in Aug 2007 and is Manufactured by SunTouch - not outsourced like other manufacturers.

New Features make the SunStat Pro the most versatile Programmable Thermostat in the Floor Heating market today:

• Dual Voltage - 1 thermostat for Either 120v or 240 - never have the wrong thermostat on the job again
• Air-sensing Mode with a Floor Temperature override limit as an option
• Regulator mode if sensor not connect or is damaged
• "Master" Control Capability - Each SunStat Pro allows other SunStat Relays to be connected to it to expand your system
• Class 2 Insulated Sensor ( 15' long) Wire which can run in the SAME CONDUIT as the power lead from your Floor Heater system
• 5/1/1 Day Programming mode or manual option
• Four Preset Schedules are included - choose one that suits you or program your own!
• Usage Monitoring - Your SunTouch SunStat Pro can report the on time of your SunTouch Floor Heat system
• 12 or 24 hour (military time) Display - your choice
• SmartStat Technology
• Easily Integrates with your home automation system (dry contact relay)

Other Features:

• Temperature Range (floor) of 40 to 99 degrees F (5 to 37 Celsius)
• Large Digital Display showing operation, mode, heat on/off, etc. LCD shows time and all functions
• Temperature displays in either F or C
• 15 Amp capacity to control up to 150 SF of SunTouch 120VAC mats per control and 300 SF of 240v SunTouch
• Can connect to NEW remote FloorStat sub control relay 500680
• Built-In Class A GFCI protection with GFCI test Light and button - 5 milliAmp trip
• 1 Year Warranty
• No Battery required - Your programming is saved in memory indefinitely
• Manual Setback / Vacation Mode for quick switching to Economy setting when leaving for an extended time
• MANUAL mode is also available to over-ride your program. Many customers like the look of this programmable model, but use it as a manual control

Included with Each Thermostat:

• 15 Foot Sensor Wire
• Complete Instructions in English, Spanish & French
• Screwdriver included for use in installation
• Wire Nuts
• Mounting Screws

Additional Information

500670 Instructions PDF Print, Read or save