The Mat Installation Kit contains everything you need to install your SunTouch Floor Warming project quickly. We recommend purchasing the installation kit if you are a first time installer. 1 Kit will cover the installation of up to 150 Sq Feet.

Included in the kit:

• A video detailing installation
• Installation Manual
• 1 Roll Super-sticky double backed tape to secure mat to the subfloor (A 108 Ft roll will typically secure up to 150 SF of Mat)
• 10 Nail Tites to secure the power leads inside the wall (if no conduit)
• 50 Wire Clips for securing the blue wire, if you choose to separate it from the mats, to the subfloor
• BONUS info from Warm Your Floor: a 6 page color article with step-by-step instructions
• Tips & Tricks sheet to make your install smooth
• Jobsite signs
• And more! Only from Warm Your Floor

Additional Information

SunTouch Installation Manual

This Basic Dial Thermostat is available for a limited time only and we offer it at this terrific price.

The NEW Digital non-programmable control is only a few dollars more and is the latest generation of floor warming thermostats.

Or, Choose the Number 1 floor heating control, brand new and packed with features...

SunStat Pro Programmable Thermostat LCD

Additional Information

FloorStat Instructions

The SunTouch 500675 NON-programmable Thermostat's NEW clean design and features make it the Top rated Basic T-stat to control your Floor heating system.

This thermostat senses the FLOOR Temperature (Using the INCLUDED 15 foot Floor Sensor Wire) and has Built-in Ground Fault Protection for your safety. Listed by ETL to UL standards for use in the USA and Canada. No need for an additional GFCI circuit in most areas. Buttons are out of sight behind a single door at the bottom of the SunStat, just below the backlit digital display.

Push a button to raise or lower temperature or simply turn the system off.

This Thermostat is Dual Voltage - 1 thermostat for either 120v or 240v - You can't get it wrong!

Several New Features were added when creating this thermostat, which was released in Sept 2007 and is Manufactured by SunTouch - not outsourced like most manufacturers.

New Features make the SunStat a terrific value if you don't want programming features to control your Floor Heating System.

• Dual Voltage - 1 thermostat for Either 120v or 240 - never have the wrong thermostat on the job again
• Air-sensing Mode with a Floor Temperature override limit as an option
• Regulator mode if sensor is not connect or is damaged
• "Master" Control Capability - Each SunStat Pro allows other SunStat Relays to be connected to it to expand your system
• Class 2 Insulated Sensor ( 15' long) Wire which can run in the SAME CONDUIT as the power lead from you Floor Heater system
• 12 or 24 hour (military time) Display - your choice
• SmartStart Control

Other Features:

• Temperature Range (floor) of 40 to 99 degrees F (5 to 37 Celsius)
• Back Light for LCD screen
• Large Digital Display showing operation, mode, heat on/off, etc. LCD shows time and all functions
• Temperature displays in either F or C
• 15 Amp capacity to control up to 150 SF of SunTouch 120VAC mats per control and 300 SF of 240v SunTouch
• Can connect to NEW remote FloorStat Control unit
• Built-In Safety - Class A GFCI protection with GFCI test Light and button - 5 milliAmp trip
• 1 Year Warranty
• No Battery required
• Manual Setback / Vacation Mode for quick switching to Economy setting when leaving for an extended time

Included with Each Thermostat:

• 15 Foot Sensor Wire (Class 2 Insulated sensor - the best in the business) can be cut shorter if you choose
• Complete Instructions in English, Spanish & French
• Screwdriver included for use in installation
• Wire Nuts
• Mounting Screws

Additional Information

500675 Instructions PDF - Read, Print or save

The SunTouch LoudMouth Monitor sounds an alarm if the SunTouch Heating Wire is cut or damaged, allowing for easy repair BEFORE the mat is covered with Mortar & Tile. We highly recommend the LoudMouth® invented and patented by SunTouch.

Connect it during the ENTIRE installation of your SunTouch Mats to monitor the Heating Elements and give yourself the assurance of a Quality Installation. The LoudMouth Monitor is Another SunTouch innovation - Our design is unique and has more features than recent imitators.

How the LoudMouth Works:

1. Insert each lead wire from the heating product into L1 and L2 terminals (no polarity) with the ground wire inserted into the G terminal. Tighten the terminal screws onto the wires.
2. Set switch to ON position.
3. Green light indicates the LoudMouth is operating.
4. The red light and alarm indicate lead wires have come loose from terminals or damage has occurred to the heating product.
5. Press the TEST button to simulate a damage condition before beginning work.

Of course, you can also monitor the installation with only your digital multi-meter to verify resistance (ohms); but you will have to watch it throughout the installation process. The Loudmouth is nicknamed "The Screamer" and is optional, but provides peace of mind during the installation process or between the installation of the Mats and the Tile (if there is a time gap between when the mats are laid out unprotected and covering them with mortar).

LoudMouth Monitor Features:

1. A very Loud Alarm Simple operation with an On/Off Switch and a TEST button
2. 9V battery operated (included)
3. A green light to indicate GO and a Red light to indicate STOP, there's damage - Fix it now
4. Screwdriver included for attaching mat leads 1 LoudMouth can be used to monitor up to 3 mats at once

** Important - a Multi Meter to measure OHMS is still required to test resistance before, during, and after installation. The Loudmouth DOES NOT replace the use of an Ohm meter - it's just another SunTouch Innovation to help your installation go smoothly.

Additional Information

How-To Connect the LoudMouth

The SunTouch 500670 Programmable Floor Heating Thermostat's NEW clean design makes it the Ultimate choice for control of your Floor heating system. This thermostat senses the FLOOR Temperature (Using the INCLUDED 15 foot Floor Sensor Wire) and has Built-in Ground Fault Protection for your safety and is listed by ETL to UL standards for use in the USA and Canada. No need for an additional GFCI circuit in most areas. Programming buttons are out of sight behind a single door at the bottom of the SunStat Pro, just below the backlit digital display.

>>> New lower special Price for a Limited Time ! <<<

This Thermostat is Dual Voltage - 1 thermostat for either 120v or 240v - You can't get it wrong!

Several New Features were added when creating this thermostat, which was released in Aug 2007 and is Manufactured by SunTouch - not outsourced like other manufacturers.

New Features make the SunStat Pro the most versatile Programmable Thermostat in the Floor Heating market today:

• Dual Voltage - 1 thermostat for Either 120v or 240 - never have the wrong thermostat on the job again
• Air-sensing Mode with a Floor Temperature override limit as an option
• Regulator mode if sensor not connect or is damaged
• "Master" Control Capability - Each SunStat Pro allows other SunStat Relays to be connected to it to expand your system
• Class 2 Insulated Sensor ( 15' long) Wire which can run in the SAME CONDUIT as the power lead from your Floor Heater system
• 5/1/1 Day Programming mode or manual option
• Four Preset Schedules are included - choose one that suits you or program your own!
• Usage Monitoring - Your SunTouch SunStat Pro can report the on time of your SunTouch Floor Heat system
• 12 or 24 hour (military time) Display - your choice
• SmartStat Technology
• Easily Integrates with your home automation system (dry contact relay)

Other Features:

• Temperature Range (floor) of 40 to 99 degrees F (5 to 37 Celsius)
• Large Digital Display showing operation, mode, heat on/off, etc. LCD shows time and all functions
• Temperature displays in either F or C
• 15 Amp capacity to control up to 150 SF of SunTouch 120VAC mats per control and 300 SF of 240v SunTouch
• Can connect to NEW remote FloorStat sub control relay 500680
• Built-In Class A GFCI protection with GFCI test Light and button - 5 milliAmp trip
• 1 Year Warranty
• No Battery required - Your programming is saved in memory indefinitely
• Manual Setback / Vacation Mode for quick switching to Economy setting when leaving for an extended time
• MANUAL mode is also available to over-ride your program. Many customers like the look of this programmable model, but use it as a manual control

Included with Each Thermostat:

• 15 Foot Sensor Wire
• Complete Instructions in English, Spanish & French
• Screwdriver included for use in installation
• Wire Nuts
• Mounting Screws

Additional Information

500670 Instructions PDF Print, Read or save