This Extra-Long sensor allows you to locate Your Thermostat farther from your heated floor area.

At 50 Ft Long, this replacement sensor solves problems if the sensor 15 Ft Long (included with each thermostat) is too short.

Customers ask: Do I need an extra floor sensor wire? We formerly recommended it. But, if you CHECK the resistance of the sensor, as indicated in the instructions, we don't feel it's necessary. Each sensor is labeled with instructions

Some customers orders an extra sensor for "peace of mind". Although it is extremely rare for a sensor to fail, they think it is a reasonable precaution to install 2 sensor wires and they consider it cheap insurance.

If you choose to purchase 2 sensors, run both sensors from the control box to the floor below and then place them between the heating elements 12 inches or more into the heated portion of the floor. You can put them side by side, but connect only one to the thermostat control. If you ever need to replace a faulty sensor, you will have one at your fingertips; simply disconnect one, and connect the back-up.

All of our controls include a sensor wire; however, a spare can come in handy if yours gets lost or damaged during installation.

Complete Repair Kit- includes all parts & complete instructions for 1 SunTouch Heating Wire repair.

Kit Includes:

• Solder Melt Splice connectors
• Small lengths of wire
• All components needed for a repair to 1 break in the Heating Wire.

1 kit needed for each repair.

This Kit is for SUNTOUCH manufactured products only. You can use this same repair kit for SunTouch Mats and WarmWire.

You will need:

A few basic tools to perform a repair - see instructions for details.

Use this special low-profile tape for installation.

Additional Information SunTouch Installation Manual

Warm Your Floor is pleased to introduce the first non metallic trowel specifically designed for use with electric radiant floor heating systems in North America. The Suntouch Cable Trowel has been thoroughly tested by professional tile installers. The Results are in! The NEW Suntouch CableTrowel is lightweight, but tough enough for commercial use. The CableTrowel is a commercial quality non-metallic trowel that WILL NOT damage the heating wire. About the Suntouch CableTrowel:

• This new tool works faster
• The CableTrowel is easier to clean than other trowels
• And it cannot damage the heating wire

Experienced tile installers know that metal trowels can become razor sharp over time and those edges are a danger to electric heating cables. The CableTrowel blade is made of durable ABS plastic so it is safer to use around heating elements. Make your electric radiant installation faster and easier - try the CableTrowel!

• The CableTrowel Will NOT damage the electric radiant heating wire or your hands! No sharp edges means no cuts in wire or you!
• The CableTrowel has a 3/8 x 3/8 notch size is suitable for larger tiles.
• It is Lighter and easier to use than the typical trowel.
• Quick Clean up since mortar washes off easily and the CableTrowel will never rust.

All these features and it costs less than $ 13!

SunTouch Super-sticky tape allows installation of up to 150 Sq Feet of SunTouch Mats.

Use this special low-profile tape to install on concrete

Additional Information

SunTouch Installation Manual

Our Digital Multi-Meter is used to check resistance (ohms) of Electric Floor Heating elements before, during, and after installation, as required by the installation manual.

ALL Electric Floor Heat installations REQUIRE the use of a digital ohm meter (aka multi-meter - must be digital). You do not have to buy this meter - you just need to have one on the job; borrow one if you can.

Dial your meter to " 200 " in the green ? range to test heating elements (Or dial to " 2000 " for resistance ranges above 199) and " 20K " or 20,000 to check the sensor wire. Get accurate readings for:

• Resistance - this is what you need for Floor Heating Installations
• DC Voltage
• AC Voltage
• Transistor Test
• Diode Test
• 19 Different Measuring Ranges

Our Compact Meter is 3-3/4" x 1-3/4" x 7/8" to easily fit in your pocket or tool box. Features an easy-to-read 1-1/2 inch digital LCD readout, positive set selector switch, and dual 24" leads. Low battery indication (12v Battery is included & Installed). Fuse (replaceable) protected circuit. Here is the scientific mumbo jumbo: DC-A: 0-200 A-2000 A-20mA-200mA. Resistance:0-200-2000-20K-200K-2000K ohm. DC-V: 0-200mV-2000mV-20V-200V-500V. AC-V: 0-200-500V.

We buy these in large quantity so we can offer them to you at this GREAT PRICE. Great to keep around the house for the Do-It-Yourselfer after Installation of your floor warming system.

Additional Information DVM810 Instructions

The Mat Installation Kit contains everything you need to install your SunTouch Floor Warming project quickly. We recommend purchasing the installation kit if you are a first time installer. 1 Kit will cover the installation of up to 150 Sq Feet.

Included in the kit:

• A video detailing installation
• Installation Manual
• 1 Roll Super-sticky double backed tape to secure mat to the subfloor (A 108 Ft roll will typically secure up to 150 SF of Mat)
• 10 Nail Tites to secure the power leads inside the wall (if no conduit)
• 50 Wire Clips for securing the blue wire, if you choose to separate it from the mats, to the subfloor
• BONUS info from Warm Your Floor: a 6 page color article with step-by-step instructions
• Tips & Tricks sheet to make your install smooth
• Jobsite signs
• And more! Only from Warm Your Floor

Additional Information

SunTouch Installation Manual

SunStat Sensor Wire is 15 Ft Long For Programmable or Non-Programmable Thermostats.

1 Sensor is included with each thermostat.

Customers ask: Do I need an extra floor sensor wire? We formerly recommended it. But, if you CHECK the resistance of the sensor, as indicated in the instructions, we don't feel it's necessary. Each sensor is labeled with instructions.

Some customers orders an extra sensor for "peace of mind". Although it is extremely rare for a sensor to fail, they think it is a reasonable precaution to install 2 sensor wires and they consider it cheap insurance.

If you choose to purchase 2 sensors, run both sensors from the control box to the floor below and then place them between the heating elements 12 inches or more into the heated portion of the floor. You can put them side by side, but connect only one to the thermostat control. If you ever need to replace a faulty sensor, you will have one at your fingertips; simply disconnect one, and connect the back-up.

All of our controls include a sensor wire; however, a spare can come in handy if yours gets lost or damaged during installation.

Each Thermostat Manufacturer uses a different sensor wire.